product FAQs


How do I store the backpack blower for less than one month?

  • Clean all foreign material from the product
  • Store it in a well-ventilated place that is inaccessible to children and keep away from corrosive agents such as garden chemicals and de-icing salts
  • Abide by all Federal and local regulations for the safe storage and handling of gasoline

How do I store the backpack blower for more than 1 month?

  • Drain all fuel from tank into a container approved for gasoline
  • Run engine until it stops

How do I install the lower handlebar? (RY13050)

  • Remove the two handlebar knobs and bolts from the hardware bag
  • Place the lower handlebar into the openings on the edger frame and make sure the hole for the hook screw is on the right side as shown

NOTE: Do not allow throttle cable to become pinched when installing the handlebar

  • Insert the bolts through the holes in the handlebar and frame and then thread the handlebar knob onto bolt and tighten securely
  • Repeat with the other side

How do I install the upper handlebar? (RY13050)

  • Remove the two handlebar knobs and bolts from the hardware bag
  • Position upper handlebar onto lower handlebar and make sure the throttle cable and throttle trigger is on the right side as shown
    NOTE: Do not allow throttle cable to become pinched when installing the handlebar.
  • Insert the bolts through the holes in the lower handlebar and upper handlebar and then thread the handlebar knob onto bolt and tighten securely

How do I install the hook screw for the starter grip? (RY13050)

  • Locate the plastic wing nut and the hook screw
  • Insert hook screw through the hole on the right side of lower handlebar and then pull the starter grip and rope into the hook screw
  • After that, thread the wing nut onto the hook screw and tighten it securely

How do I fill up my edger with fuel?

  • Clean the surface around the fuel cap to prevent contamination
  • Then, loosen the fuel cap slowly
  • Make sure to rest the cap on a clean surface.
  • Then pour fuel into the tank. Avoid spillage.
  • Prior to replacing the fuel cap, clean and inspect the gasket.
  • Immediately replace fuel cap and hand tighten. Wipe up any fuel spillage.
    NOTE: It is normal for smoke to be emitted from a new engine after first use.

WARNING: Always shut off engine before fueling. Never add fuel to a machine with a running or hot engine. Move at least 30 ft. from refueling site before starting engine. Do not smoke and stay away from open flames and sparks. Failure to safely handle fuel could result in serious per¬sonal injury.

  • Always shut off engine before fueling. Never add fuel to a machine with a running or hot engine. Move at least 30 ft. from refueling site before starting engine. Do not smoke and stay away from open flames and sparks. Failure to safely handle

How do I start and stop my edger?

To start an engine that is cold or has run dry:

  • Fill the fuel tank, if necessary. Always use the proper gasoline
  • Place the engine switch in the ON ( | ) position

NOTE: Do not engage the throttle trigger during the starting process

  • Slowly push the primer bulb ten times and then set the start lever to the START position
  • Stand behind the edger and place your left hand on the handlebar
  • Using your right hand, pull the starter grip and rope until the engine runs

NOTE: Return the starter grip and rope gently to the eyelet. Do not allow the cord to snap back.

  • Set the Start lever back to the RUN position.

NOTE: If the engine dies, leave the start lever in the RUN position and pull the starter grip and rope until the engine starts.

  • Engage the throttle lever to operate.

To start a warm engine:

  • Move the start lever to the START position and then im¬mediately back to the RUN position

NOTE: This will set the carburetor to a fast idle setting for easier starting

  • Pull the starter grip and rope until the engine starts

To stop the engine:

  • Release the throttle lever
  • Move the engine switch to the OFF ( O ) position

How do I adjust the blade of my edger?

  • Stop the engine and remove the spark plug wire
  • Loosen the adjusting knob and move the wheel arm up to increase the depth or down to decrease the depth
  • After adjustment is complete, tighten the adjusting knob securely
  • Replace the spark plug wire and start the unit

NOTE: Adjust the blade depth from 1/2 in. to 1 in. deep initially. Make a shallow cut to test the cutting depth. If the cutting depth needs adjusting, this should be

How do I adjust the curb hopper wheel?

  • Stop the engine and remove the spark plug wire
  • Loosen the adjusting knob and move the wheel down to depth of curb
  • After adjustment is complete, make sure the bolt is aligned with one of the adjusting holes and tighten the adjusting knob securely
  • Replace the spark plug wire and start the unit

How do I replace my blade on my edger?

  • Replace blade when its worn down to indicator hole on blade is worn unevenly

WARNING: Wear gloves during blade replacement. The blade is sharp and may cut you

  • Stop the engine and remove the spark plug wire
  • Using a 5/16 in. hex wrench to hold blade shaft, use a24 mm socket wrench to turn the blade nut counterclockwise and remove
  • Remove the old blade from the edger shaft
  • Clean debris from the edger shaft assembly and slide new blade onto edger shaft
  • Install the blade nut onto the edger shaft
  • Using a 5/16 in. hex wrench to hold blade shaft, thread blade nut, clockwise, on blade shaft with 24 mm socket wrench and tighten securely

How do I store my edger?

  • Clean all foreign material from the product
  • Store the idle unit indoors in a dry, well-ventilated area that is out of reach of children
  • Always keep away from corrosive agents such as garden chemicals and de-icing salts

Note: Abide by all ISO and local regulations for safe storage and handling of gasoline

How do I store my edge for longer than one month?

  • Drain all the fuel from the tank into a container approved for gasoline and then run the engine until it stops

How do I connect the power head to the edger attachment? (RY40030)

  • Remove the battery pack from the power head if installed
  • Align the arrows on the edger attachment and the power head
  • Insert the plug on the attachment into the opening coupler and make sure the plug is fully seated
  • Then, slide the threaded coupler on the power head onto the treaded base on the attachment and turn the coupler clockwise and tighten securely

Note: Once it is assembled correctly, the edger attachment and power head should not separate when pulled. If it does repeat the steps above until the pieces do not detach

Warning: Failure to secure the pieces together tightly may result in serious injury

How do I adjust the front handle? (RY40030)

  • First remove the battery pack and then set the edger on a flat surface
  • Turn the knob counterclockwise and loosen the handle
  • Set the edger on a flat surface and turn the knob counterclockwise to loosen the handle.
  • For edging, adjust the handle downward.
  • Turn the knob clockwise until the handle is

How to start the edger?

  • Press and hold the lock-out and then depress the switch trigger.

How do I stop the edger?

  • Release the switch trigger to stop the edger
  • Upon release of the switch trigger, the lock-out will automatically reset to the locked position

How do I adjust the depth of cut on the edger?

  • Remove the battery pack and then loosen the depth adjusting lever
  • Move the wheel arm up to increase the depth or down to decrease the depth
  • Make sure the lever locks into one of four positions.
  • Then replace the battery pack.

NOTE: Adjust the blade depth from 1/2 in. to 1 in. deep initially. Make a shallow cut to test the cutting depth. If the cutting depth needs adjusting, this should be desired progressively until the desired depth is reached


How do I Replace the blade on the edger?

  • Replace blades when worn down to indicator hole on blade
  • Remove the battery pack and wear gloves when handling blade
  • Align the slot in the flange washer with the slot in the gear case ring; place the holding pin through both slots to secure in place
  • Using the wrench (included), turn the blade nut counterclockwise to loosen
  • Remove the old blade from the motor shaft and clean debris from the edger shaft, flange washer and cupped washer
  • Center the new blade on the flange washer, making sure the blade sits flat
  • Properly install the cupped washer with the raised center area with the hole not touching the blade and the outer ring of the cupped washer touching the blade
  • Install the blade nut onto the motor shaft and reinsert the holding pin into the slots as described above
  • Using a wrench, turn the blade nut clockwise onto the edger shaft and tighten securely

WARNING: Always make sure the blade is correctly installed and securely fastened before each use. Failure to properly install the blade may result in serious personal injury.

How do I store the edger?

  • Remove the battery pack from the power head before storing
  • Clean all foreign material from the edger

NOTE: Store it in a place that is inaccessible to children and keep it away from corrosive agents such as garden chemicals and de-icing salts

How do you installing the vacuum bag on the blower? (RY09056)

  • Remove the nozzle and upper blower tube from the blower by twisting and removing from the blower housing outlet
  • Unzip the vacuum bag and push the vacuum bag adaptor through the opening opposite the zipper as shown
  • Make sure the wider end of the adaptor remains on the inside of the vacuum bag when installed properly
  • Align the raised slots on the vacuum bag adaptor with the raised locking tabs on the blower housing outlet
  • Push the vacuum bag adaptor onto the housing and twist to lock into place
  • Rotate the vacuum bag until the shoulder strap is upright
  • Make sure the vacuum bag is zipped and closed before starting the unit