MORE PORTABILITY. MORE CUTS.
POWERFUL 15A MOTOR WITH BLADE BRAKE.
CAST ALUMINUM TABLETOP FOR A FLAT, DURABLE AND LIGHTWEIGHT WORK SURFACE.
STEEL ROLL CAGE DESIGN FOR ADDED DURABILITY AND FRAME STRENGTH.
INTEGRATED ON BOARD STORAGE FOR ALL ACCESSORIES.
- Cut Capacities:
- Depth of cut at 90: 3 In.
- Cut Capacities:
- Depth of cut at 45: 2-1/2 In.
- Cut Capacities:
- Dado Width: 1/2 In. with dado throat plate (not included)
- Rip Capacities:
- 27 In. right of blade
- Rip Capacities:
- 7 In. left of blade
- 15 Amp, 120V
- No Load Speed
10 in.Expanded Capacity Table Saw with Rolling Stand
10 in.Expanded Capacity Table Saw with Rolling Stand is rated out of 5 by 72.
Rated 3 out of 5 by Sawsaw from Get the job done. It got the job done although, it wasn't quite what I was expecting. It was simple to build although it was missing a screw that secured the leg (simple fix). The next thing that bothered me, is the lever that loosens the blade to adjust the angle. It is made out of plastic and stripped the 1st time I adjusted the angle, I had to use a wrench every time that I needed to adjust it after that. Finally, I expect the arrow that determines the angle to point at the angle that you need. It was a surprise when a 45 degree cut was not 45 degrees since I had the point of the maker on 45 degrees but it need to be slightly off.
Date published: 2020-05-13
Rated 4 out of 5 by Dunnothebull from Really, Really Good! But not Great. Does a really good job. I have ripped a ton of lumber with it. The motor is plenty powerful when you blade is sharp, once it starts to go the motor shows it's lack of power. The stand is a little on the flimsy side, and part of the good part about being lite and mobile also makes the saw a little top heavy. I would like to have some more weight at the bottom It is easy to tip. And lastly, and easily my biggest complaint is the rip fencel. It is just too small. Less than a quarter inch high. Not sure why it is like this. The fence is a couple inches high, but it has a quarter inch lip.See photo.
Date published: 2020-07-21
Rated 5 out of 5 by Ace70 from Satisfied Ryobi Table Saw Owner This is a nice functioning table saw. I replaced a dated table saw. This is a well made saw, which is perfect for my DIY jobs. I did replace the 10 inch saw with a 60 tooth carbide saw blade. I did so, to ensure clean cuts on my projects. This was my personal preference only. The many features of this saw is what I really like. The folding stand with mounting hardware, the ability to roll the table saw and store away, a push stick, a miter gauge, a rip fence, guarding assembly and anti-kickback pawls are all nice features. I’ve used this for several projects during my short time of ownership, and overall I am very happy this table saw.
Date published: 2021-03-09
Rated 5 out of 5 by chuckwagonga from Nice Portable Table Saw I purchased this saw about a month ago over the 500 dollar Rigid Table Saw. So far it's cut is accurate and smooth thanks to an upgraded 80 tooth blade. I had a little trouble getting the wheels on as the threads were barely visible and couldn't get the nut to thread on. After chipping away some paint and a little persuasion, I was able to get the wheel secure. Other than that, it works great. No problem going through 2x4's, MDF, Base trim, LVT plank flooring. I recommend connecting a vacuum for less mess. So far I'm glad i made the purchase.
Date published: 2020-12-16
Rated 5 out of 5 by VicM from Great Table Saw! I got this saw as a gift for my birthday. It helped me cut my work down by more than half, and is built sturdy. I have yet to have any issues with the cuts or the build. The only thing I do recommend is to get another blade, depending on the kind of work you do would determine that of course. Even with the Ryobi brand one that came with it, I was able to get to work right away. I felt like a child on Christmas opening up a new toy, and one that I can tell you I use everyday. Great product, and it wont be the last Ryobi tool I get, hopefully!
Date published: 2020-09-22
Rated 4 out of 5 by Rob the builder from Nice saw but stand has some issues. This saw works well but it has a few shortcomings. The biggest fault I found was with the stand. It is very difficult to break down the stand and use the wheels to move the saw. If you keep your saw upright and don’t move it around then this is not a big deal, but if you need to move your saw to use you’ll find this saw not very portable. Also, the clips that lock the stand up or down are pretty insecure. Instructions for how to remove the included 24 tooth saw were confusing and diagrams were not clear.
Date published: 2020-10-09
Rated 5 out of 5 by HANDY AL from GREAT i bought this back in August put assembled and found that the clamps were not the right size. After i registered the three items i call regarding the clamps and the plastic inserts Ryobi customer service then sent me new ones the clamp plastic insert and the nuts. I was able to replace them and now it is great it is safe and fun to use it. i have lots of projects that i will be working on my days off. i think if that the price was a little lower that lot of do it your selfer would buy it at this time have no photos.
Date published: 2020-09-21
Rated 4 out of 5 by utec from Good for the price The blade is aligned parallel to the table and at 90 degrees. The fence was very slightly curved, and they are sending a replacement. I attached an auxiliary fence for the time being, holes were available to bolt through. Love the dust collection port. My only complaint is that the table is not level to the floor - it's a half inch low on the fence side, so things slide off the table.
Date published: 2020-07-17