The RYOBI Pressure Washer Trigger Gun is designed to replace outworn or damaged trigger handles, can be used with almost any gas or electric pressure washer up to 3,300 psi.This durable replacement trigger gun has over-molded grips for user comfort and control.
- Max PSI: 3300
- Material: High-density Poly Ethaline
- Pressure Washer Trigger Gun
PRESSURE WASHER TRIGGER GUN
PRESSURE WASHER TRIGGER GUN is rated out of 5 by 13.
Rated 1 out of 5 by Mayhem86 from Terrible design - failure is inevitable After less than a year of service and maybe 5 or 6 uses, the trigger gun would not operate and started leaking down the valve stem. By applying pressure to the side of the hose assembly you can get the valve to open and the sprayer to operate, but clearly you're not going to work like that. I disassembled the trigger wand. Pulling the trigger causes a piston to depress on top of the valve, allowing water to flow. But because everything is plastic inside except for the valve stem, which comes into contact with a very tiny metal rod installed in the spray wand. The slightest wear causes the entire levering mechanism to shift and therefore fail to operate as designed. Poor design.
Date published: 2019-05-29
Rated 1 out of 5 by Unhappy Customer 1000 from Extremely Poorly Build | Poor Quality at best! I've had this product for about 6-7 months, total uses about 4. The trigger gun leaks all over the place. I've seen the reviews and I've contacted the number they tell you to call after they apologize for a poorly constructed product. I was told that it was out of warranty and I needed to buy a new one. That would make sense if I had the product for a longer time. 4 uses in total!!! As a consumer think about anything else you may buy that only last 4 uses? It's completly unexpectable....
Date published: 2019-08-21
Rated 1 out of 5 by Britt13 from Poor quality internals This product has horrible internal parts. This is the second one I have bought and had the same issue with both. There is a bushing inside the internal valve that breaks and causes water to flow no matter where the trigger is at. I would not recommend this product and honestly has left a bad taste for ryobi products in general.
Date published: 2019-02-05
Rated 1 out of 5 by Blue Sky Mom from Gun handle broke after 4 uses While the product does an excellent job of cleaning, after only 4 uses, something broke in the gun trigger, and it would not stop spraying. The pressure also went down quite a bit, and water started spraying from the trigger connection. Im trying to figure out how to replace the part, and am rather frustrated..
Date published: 2018-10-21
Rated 1 out of 5 by Ron46 from Defective Triger gun I bought this 2000 psi sprayer in April and have used it only 3 times. The last time the handle started leaking and the spray was weak. Apparently the valve that opens the water flow to the actual spray is leaking like a sieve. Water ran down my arms and onto my shoes while trying to clean lanai screens.
Date published: 2018-09-23
Rated 4 out of 5 by thetoysurgeon from Sprayer Handle has bad O-rings. I bought this Ryobi Pressure Washer and used it once and it started leaking at the handle/wand connection. When you screw it down the brass end of the wand cuts the o-ring when you tighten it down. I replaced the o-ring with lube and it still gets cut. Would like to know how to keep this O-ring intact?
Date published: 2019-09-29
Rated 5 out of 5 by StevenD from Simple fix for leaking trigger gun The first time I attempted to powerwash this year the gun leaked. I changed the o ring but it didn't help. Bought this replacement handle and it worked GREAT!!
Date published: 2017-06-21
Rated 5 out of 5 by jschronce from Works great! This wand was a direct replacement for the one that came with the Ryobi pressure washer I've had for over a year. Works just like the original.
Date published: 2019-06-29