Return to Projects Listing
HANGING GARDEN
  • HANGING GARDEN

HANGING GARDEN

A hanging garden in 2 hours.

Steps


Lay out the holes.

Use a pencil to mark the hole locations on a board. Make sure you leave about 2" between the flower pot holes and about 1" between the rope holes and edges of the board.


Lay out the holes. 

Use a pencil to mark the hole locations on a board. Make sure you leave about 2" between the flower pot holes and about 1" between the rope holes and edges of the board.
×

Cut the boards.

Once you have established the hole locations, you can trim the boards to the desired length with a circular saw. If you lay out the boards in advance, you can have the boards cut for you at Home Depot. I purchased 6' boards and cut them in half.


Cut the boards. 

Once you have established the hole locations, you can trim the boards to the desired length with a circular saw. If you lay out the boards in advance, you can have the boards cut for you at Home Depot. I purchased 6' boards and cut them in half.
×

Drill pilot holes.

The key to this project is making sure the holes are aligned. Rather than marking each board, I simply marked one and drilled small pilot holes through the entire stack of boards. These small holes will serve as guides for the hole saw.


Drill pilot holes. 

The key to this project is making sure the holes are aligned. Rather than marking each board, I simply marked one and drilled small pilot holes through the entire stack of boards. These small holes will serve as guides for the hole saw.
×

Cut holes for pots.

Hole saws can be a bit tricky to handle. The larger diameters can generate a lot of friction with wood so it's important to properly secure the boards and have a firm grip on the drill. I clamped the boards two at a time to a work table. Set your drill to the drilling mode at the highest speed
and use both hands. The saw will occasionally freeze up and bind against the wood, so be patient and try and keep the drill perpendicular to the board.


Cut holes for pots. 

Hole saws can be a bit tricky to handle. The larger diameters can generate a lot of friction with wood so it's important to properly secure the boards and have a firm grip on the drill. I clamped the boards two at a time to a work table. Set your drill to the drilling mode at the highest speed 
and use both hands. The saw will occasionally freeze up and bind against the wood, so be patient and try and keep the drill perpendicular to the board.
×

Drill holes for rope.

I used a 5/16" drill bit for the 1/4" rope. It's important to have a tight fit for the rope so that the zip ties create a stopper to keep the boards from sliding.


Drill holes for rope. 

I used a 5/16" drill bit for the 1/4" rope. It's important to have a tight fit for the rope so that the zip ties create a stopper to keep the boards from sliding.
×

Sand the boards.

Pine is a soft wood, so you can hand sand the boards pretty quickly. I used an orbital sander and sanded them with 220 grit paper.


Sand the boards. 

Pine is a soft wood, so you can hand sand the boards pretty quickly. I used an orbital sander and sanded them with 220 grit paper.
×

String the boards..

Thread the rope through the holes and tie a knot at the bottom.


String the boards.. 

Thread the rope through the holes and tie a knot at the bottom.
×

Hang the garden.

Make sure you are hanging the garden from a location that can support the weight. Closet shelf brackets work well. Try your best to level the boards. You can adjust the leveling with the zip ties.


Hang the garden. 

Make sure you are hanging the garden from a location that can support the weight. Closet shelf brackets work well. Try your best to level the boards. You can adjust the leveling with the zip ties.
×

Secure the boards.

You want to make sure you have adequate space for the plants between the boards. Adjust the boards into the right location and use zip ties under the rope holes to secure them. I started with a single zip tie with a loose fit, which allowed me to slide the zip tie along the rope into the right position. Once I got the right placement, I added 2 to 3 tight zip ties underneath each rope hole to make sure the boards wouldn't slide under the weight of the potted plants.


Secure the boards. 

You want to make sure you have adequate space for the plants between the boards. Adjust the boards into the right location and use zip ties under the rope holes to secure them. I started with a single zip tie with a loose fit, which allowed me to slide the zip tie along the rope into the right position. Once I got the right placement, I added 2 to 3 tight zip ties underneath each rope hole to make sure the boards wouldn't slide under the weight of the potted plants.
×

Place the plants.

Put your potted plants in the holes, step back and enjoy!

Options: You can use the same method to make a single shelf supported by brackets. Use small glass bottles and wire to catch the water that drains through the pots. Terra cotta can be painted, so there are all sorts of nice color combinations you can play with.


Place the plants. 

Put your potted plants in the holes, step back and enjoy! 

Options: You can use the same method to make a single shelf supported by brackets. Use small glass bottles and wire to catch the water that drains through the pots. Terra cotta can be painted, so there are all sorts of nice color combinations you can play with.
×
View All Steps
spacer

Comments (1) Sign In To Follow Project


uWishuCould
uWishuCould

Sweet! ... on my 2Do list now ... tysm

View All Comments
spacer

Homemade Modern

Homemade Modern

All Projects | Profile


  • share

Project Information

Difficulty: Easy

Materials Used:

  • 4” to 5” Terra Cotta Flower Pots

  • ¾” Pine Boards

  • Rope

  • Zip Ties


also by Homemade Modern


Related Projects


Forgot your password? Click here.

Don't have a RYOBI Account? Sign Up Now.

×