Return to Projects Listing
ENTRY TABLE
  • ENTRY TABLE

ENTRY TABLE

Sofa tables are highly sought after items, but often aren’t the right height, width or length that you need. So, why not make your own? In this post, I’m going to make a sofa table/entrance way table that is both rustic and chic and can be customized to the exact measurements you need. The wood was purchased at a lumber yard down the road but you could easily use scrap barn wood, or any other wood of your choice and treat the surface to match the other items in your home. The most time was spent prepping the wood to match my home. The actual construction of the table flew by and was super easy. This was my first time using the miter saw and this project made my introduction to this tool very easy and seamless.

Steps


Medium f94bcda4 843f 4345 9923 08f8ced35235

I bought oak from a lumber yard down the road and cut it in half with the RYOBI sliding miter saw. Once the 8’ wood was cut into two 4’ boards, I hand sanded each piece, which can be done with a RYOBI hand sander or with sand paper by hand.


F94bcda4 843f 4345 9923 08f8ced35235
×
Medium 8ff2d536 93c1 4638 aafa 236bba4a8698

I chose to stain my wood a dark walnut to match the wood in my living room, but any stain will work. Apply one coat with a brush and wipe the excess off with a rag. Stain all sides of the wood.


8ff2d536 93c1 4638 aafa 236bba4a8698
×
Medium 38f3df84 c984 42f7 ab51 24662f80ad95

The next step is to polyurethane the top surface of the wood. I only apply this clear gloss to the sides that will be facing out and up. I love the personality that knots bring to the wood, so I usually choose the knotty side to face up. Apply 2-3 coats of polyurethane to the wood. Let dry for an hour or two until the surface isn’t sticky. The wood prepping is now over.


38f3df84 c984 42f7 ab51 24662f80ad95
×
Medium 9767d957 1a6c 4be3 a741 698badd2f504

We will begin the construction of the sofa table from the bottom and work our way up. Screw together the flanges to both sides of the 10” nipple pipe. With both screwed tight, place the bottom shelf on its back with the under side facing up. Stack the legs on all four corners flush with the edges and mark holes within each of the flange holes to pinpoint where to drill a hole.


9767d957 1a6c 4be3 a741 698badd2f504
×
Medium c7a71649 b138 41bd a919 d5651c44ace5

Drill holes in all four corners.


C7a71649 b138 41bd a919 d5651c44ace5
×
Medium 3dbffaa2 0662 4415 9359 f5bb14b4a12d

Place the leg on top of the drilled hole and now screw the wood screws into the holes.


3dbffaa2 0662 4415 9359 f5bb14b4a12d
×
Medium 7c9e7d77 79e8 4ee8 a933 54a4aba34de6

With the bottom shelf done, flip the shelf over so its standing upright and repeat the same process now with the 18” nipple pipes standing on top of the polyurethane surface of the bottom shelf.


7c9e7d77 79e8 4ee8 a933 54a4aba34de6
×
Medium c648f5b9 19b2 43b7 9d0f 582636eb9f81

Slip the entire table over with the top shelf on its back to screw the 18” nipple pipes in to the top board.


C648f5b9 19b2 43b7 9d0f 582636eb9f81
×
Medium cb7239c3 4620 488d a182 afbfa33bb63d

If the legs appear to be crooked here is the trick (and you’ll need two people for this one step only). One person needs to hold the pipe down to the corner flush with the edges. Contrary to the other steps, drill the hole through the flange this time and immediately follow this with screwing in the first screw. Drill and screw one hole at a time. This holds the entire flange down enough to drill holes and screw the other screws in without straining to hold it down.


Cb7239c3 4620 488d a182 afbfa33bb63d
×
Medium bdd7b523 4f4f 4d2d 8cb2 7acbbb8a2f17

Repeat with all four corners.


Bdd7b523 4f4f 4d2d 8cb2 7acbbb8a2f17
×
Medium 9991274f 9fda 433e 93b6 a67fad0a7993

You're done! Doll up your table with some trinkets and enjoy the entrance way/sofa table customized for your home.

For more DIY projects from Life in High Cotton, visit lifeinhighcotton.wordpress.com.


9991274f 9fda 433e 93b6 a67fad0a7993
×
Life in High Cotton

Life in High Cotton

All Projects | Profile


  • share

Project Information

Difficulty: Easy

Materials Used:

  • (1) Oak board 2”x10”x8’ cut into 2 pieces each 2”x10”x4’

  • (1) Can of Wood stain

  • (1) Can of clear semi-gloss Polyurethane

  • (1) Paint brush

  • (4) 10”x3/4” Galvanized nipple pipe

  • (4) 18”x 3/4” Galvanized nipple pipe

  • (16) 3/4” Galvanized flanges

  • (48) #12 1 ¼” wood screws


  • Related Projects


    Recently Viewed Projects


    Forgot your password? Click here.

    Don't have a RYOBI Account? Sign Up Now.

    ×