Return to Projects Listing
TABLE MADE FROM DOOR
  • TABLE MADE FROM DOOR

TABLE MADE FROM DOOR

We had an old door lying around that we wanted to repurpose and give a new life. We were also in need of a new table for our back porch redo, the door gave us the inspiration. We wanted the table to have a rustic look; so the door, a few 2 x 4’s, 4 x 4’s and a box of screws and we had all the supplies we needed for a easy wonderful addition to our backyard makeover. (If you want a little less rustic look you could use pocket hole screws.)

Steps


BEFORE YOU BEGIN
Supplies:
• (1) 4 x 4 x 10
• (1) 2 x 4 x 4
• (1) 2 x 4 x 10
• (1) 2 x 4 x 12
• A box of #8 3 inch wood screws
• An old door
• A piece of glass
• Rubber stoppers

Tools:
• RYOBI 10 Inch Sliding Compound Miter Saw
• RYOBI Cordless Lithium Dril


×

Starting off you will need to measure the length of your door. Ours was 28 inches x 76 inches. (Don’t assume yours is the same size as ours, make sure to adjust your supply list to your table size, not ours.) We wanted a 2 inch overhang on all sides for the table

Using the RYOBI Miter Saw;
• Cut the 4 x 4 post into (4) 30 inch sections
• Cut the 2 x 4 x 10 into (1) 69 inch piece and (2) 24 inch pieces
• Cut the 2 x 4 x 4 into (2) 21 inch pieces.
• Cut the 2 x 4 x 12 into (1) 69 inch piece and (3) 21 inch pieces. The 21 inch pieces will be the inside supports.
(Remember to adjust your measurements for your door size.)


×

Lay out both of your cut 2 x 4’s that are 69 inches and the (2) cut 2 x 4’s that are 24 inches so that they make a box. The 69 inch pieces should butt into the 24 inch pieces so that the box measures 6 feet x 2 feet.


×

Place a 4 x 4 in each corner. Square off the two pieces and screw each corner into your 4 x 4 with the 3 inch screws. (I’d use at least 3 screws.)


×
Medium 6c061cc0 eaea 422e 97b6 32524da66342

Butt a 2 x 4 that was cut to 21 inches up next to the inside of the 4 x 4 post on both ends and screw them in. Your 4 x 4 should now be sandwiched by the 21 inch & 24 inch 2 x 4 with the 69 inch 2 x 4 on the outside.


6c061cc0 eaea 422e 97b6 32524da66342
×

Take the remaining (3) 21 inch 2 x 4 pieces; place one in the middle of the table and the other two between that one and the end of the table frame. Screw them all in with the 3 inch screws, at least 2 screws on each board on both sides.


×

Turn the table base upright. Screw the door to the table base. You can use the 3 inch screws and screw in from the top or you can get some longer screws and come in from the bottom, but pre-drill the holes. You can also use a pocket hole screw on the inside.


×

Get some glass cut from your local glass store to the exact size of your door. Place some rubber stoppers on one side of the glass, this will be the side that sits on the door.


×
Medium 9d5f5fb2 bfc5 4b99 a3e4 545280825544

Set your tablescape and enjoy an evening with your friends.


9d5f5fb2 bfc5 4b99 a3e4 545280825544
×

335ba613 33ad 4ad4 be3d c8b7bdf683e8
×
The Handmade Home

The Handmade Home

All Projects | Profile


  • share

Project Information

Difficulty: Easy

Materials Used:

  • (1) 4 x 4 x 10

  • (1) 2 x 4 x 4

  • (1) 2 x 4 x 10

  • (1) 2 x 4 x 12

  • A box of #8 3 inch wood screws

  • An old door

  • A piece of glass

  • Rubber stoppers

  • also by The Handmade Home


    Related Projects


    Recently Viewed Projects


    Forgot your password? Click here.

    Don't have a RYOBI Account? Sign Up Now.

    ×