Add Your Project

  • Home
  • How To's
  • Crafts & Decor
  • [#<Breadcrumb:0x00007f72297c31a0 @title="Home", @path="/nation">, #<Breadcrumb:0x00007f72297c2fc0 @title="How To's", @path="/nation/how-tos">, #<Breadcrumb:0x00007f722962e1c8 @title="Crafts & Decor", @path="/nation/how-tos/category/crafts-decor">]

Paper Towel Dispenser

  • August 17, 2017


Assemble crown molding into two outside corners to box in a decorative holder for paper towel or hand towels. Add a slot at the bottom and a lid on top to complete the look.

Show More
  1. Project Steps

    1. Step: 1

      Large 14f0f11b d2c9 4891 abbc 21c27b71b4d3

      Step 1 – Size and Prep the Base Using a miter saw, cut the base of the paper towel holder to size (9-inches-long-by-3¼-inches-wide) from a piece of ½-inch-thick board or scrap plywood. Mark a rectangle 7½-inches-long-by-1¾-inches-wide on the center of the cut board. Using a drill fitted with a 5/8-inch spade bit, drill holes through the board at each corner of the rectangle to create the rounded corners of the opening.

    2. Step: 2

      Large abe28ef0 0d15 446f 8313 fe9c0abe1d22

      Step 2 – Cut the Opening Clamp the board to the work surface. Using a jigsaw, cut the line between the holes drilled in step one to complete the rectangular opening.

    3. Step: 3

      Large c3f0a157 1a5b 4e53 8665 9e952dab2bab

      Step 3 – Set up the Saw To cut the crown molding flat on a compound miter saw, tilt the bevel of the blade to 33.9-degrees, and then twist the miter angle of the blade to 31.6-degrees. (Note these adjustments are for crown molding with a 52-degree/38-degree molding. If you're working with 45/45 crown molding adjust the bevel to 30-degrees and the miter to 35.46)

    4. Step: 4

      Large 8499ff46 2adf 4890 a1ad 3fbccd566798

      Step 4 – Cut the First Piece of Crown Molding On the bottom edge of the crown molding, mark 3¼-inches from the end of the board. Orient the molding on the saw so that the miter creates a long point at the top edge of the molding and the bevel cuts back into the thickness of the molding.

    5. Step: 5

      Large a49be65d 315e 4d9a bddf ea07b9a294a6

      Step 5 – Finish Cutting the Crown Molding Finish cutting the molding as shown so that the bottom edge of each piece fits against its corresponding edge of the base board cut in step one.

    6. Step: 6

      Large 5e317291 f627 4265 a75a 3c5daddb509d

      Step 6 – Cut the Back Miter the ends of the ½-inch-thick back board to 38-degrees, or the spring angle of the crown molding.

    7. Step: 7

      Large 41970d43 f441 4e3b ad14 b715d74ea332

      Step 7 – Assemble the Base and Back Apply wood glue to the edge of the base board. Center the back on the edge of the base, and then nail it into place using a pneumatic nail gun and 1-inch brad nails.

    8. Step: 8

      Large 664cb0ca 385d 4fd4 b257 66fa958896d5

      Step 8 – Add the Crown Molding Side Place the first piece of crown molding along the edge of the base so that it covers the edge of the back board. Apply glue to the edge of the base and the back boards. Nail through the crown and into the base and back boards to hold it in place.

    9. Step: 9

      Large 3c1372e1 9580 42b4 917b 041cd48e0742

      Step 9 – Attach the Front Apply wood glue to the edge of the installed crown molding piece, and along the front edge of the base board. Place the center piece of crown molding in place, concentrating on the joint with the installed crown. Nail through the crown and into the base board to hold the piece in place.

    10. Step: 10

      Large d6488dae 29e2 42b5 bf86 e00f61f54f99

      Step 10 – Attach the Last Side Glue and secure the remaining piece of crown molding. Add painter's tape across the joints to hold them tight while the glue dries.

    11. Step: 11

      Large 0b7390e0 31ee 44ae 98a3 f70ad4810305

      Step 11 – Cut and Place the Lid Cut a piece of ¼-inch board or scrap plywood to a size of 14¼-inches-long-by-6-inches wide. Place the board onto the assembly as a removable cap.

Comments (2)

  • Clever! Just wondering what size paper towels fit.

    By finman326

Members Also Viewed

back to top?

Asset 1

Join RYOBI Nation

We're so glad you're here! Let's get started.


Let's build your project feed!

Select some categories to pick the kinds of projects that show up on your home page:

Welcome to Nation

welcome_r2 graphic
Welcome to your RYOBI Nation quick start guide, a fast and easy way to see everything that's waiting for you!
project_feed_r1 graphic
Your feed shows the latest projects from the categories you’ve selected, right on your homepage!
upload_r2 graphic
Are you working on something awesome? Upload your DIY projects today, and share with other members.
contests_r2 graphic
We award monthly and annual prizes for the best projects, worth up to $2500 in RYOBI tools! That’s a lot of hardware, and it could all be yours.
connect_r2 graphic
RYOBI Nation is a positive connection between people who are creating great things.
You can follow fellow members, like their projects, and comment to let them know they’re doing a great job.
notifications_r1 graphic
Come back to RYOBI Nation often to see what is new and to stay in touch.
If you're on a mobile device, don't forget you can add RYOBI Nation to your home screen for quick access to your project feed.