Your one stop destination for tips & techniques, manuals, troubleshooting, FAQs and more!

2 Cycle Full Crank Power Head

2 Cycle Full Crank Power Head

RY251PH

Not Your Tool? Search Again

Tips & Techniques

Videos & Diagrams

In The Box

Manuals

  • 25cc 2-cycle Power Head - ry251ph, ry25phemc

  • 25cc 2-cycle Power Head - ry251ph, ry25phemc

REGISTRATION & WARRANTY

Ryobi three year warranty logo

All RYOBI Outdoor Products purchased on or after 1.1.09 are covered by a 3-year warranty. All RYOBI Portable Power Tools and Bench/Stationary tools purchased on or after 1.1.11 are covered by a 3-year warranty.

Learn More Register Tool

TROUBLESHOOTING & FAQs

What is the best way to cut weeds and grass using my string trimmer?
  • Keep your string trimmer tilted toward the area being cut
  • Pass the unit from left to right (if using a curved shaft string trimmer) and from right to left (if using a straight shaft string trimmer). By following these directional cutting paths, you will avoid having debris and grass clippings from being directed back at yourself.
  • Use the top of the line to do the cutting. Do not force the string head into uncut grass; this could cause the trimmer to bog down.
  • Avoid trees, shrubs wire and picket fences.
How should I store my 2 Cycle Gas String Trimmer?
  • Clean all foreign material from the product. Store idle unit in a garage or shed in a dry, well-ventilated area that is inaccessible to children. Keep away from corrosive agents such as garden chemicals and de-icing salts. Abide by all local regulations for the safe store and handling of gasoline

When storing 1 month or longer:

  • Drain all fuel from string trimmer tank into a container approved for gasoline. Run engine until it stops
What is the correct fuel mixture to use with my 2 cycle engine RYOBI Outdoor Product?

Your 2-cycle engine requires pre-mixing gasoline and 2-cycle lubricant. Pre-mix unleaded gasoline and 2-cycle engine lubricant in a clean gas container. DO NOT mix quantities larger than usable in a 30-day period. Do not use automotive lubricant or 2-cycle outboard lubricant. We recommend using a RYOBI/Homelite premium 2-cycle oil or a PowerCare 2-cycle oil.

Filling your tank:

  • Clean surface around fuel cap to prevent contamination
  • Loosen fuel cap slowly. Rest the cap on a clean surface.
  • Carefully pour fuel into the tank. Avoid spillage.
  • Prior to replacing the fuel cap, clean around the gasket.
  • Immediately replace fuel cap and hand tighten. Wipe up any fuel spillage

Note: it is normal for smoke to be emitted from a new engine after fist use.

How do I start my RYOBI 2 Cycle String Trimmer?

To start a cold engine:

  • Slowly press the primer bulb 10 times.
  • Set the choke lever to the START (A) position.
  • Squeeze the throttle trigger fully and pull the starter handle until the engine runs. Do not pull the start grim more than six (6) times.

NOTE: Keep the throttle trigger squeezed fully through remaining steps. If the engine does not start, start over at the first step with pressing the primer bulb.

  • Allow the engine to run for 10 second, then set the choke lever to the RUN (B) position.

To start a warm engine:

Slowly press the primer bulb 10 times.

Set the choke lever to the RUN (B) position.

Squeeze the throttle trigger fully and pull the starter handle until the engine runs.

How do I stop my RYOBI Gas String Trimmer?

To stop the engine, depress the STOP switch to the stop position

How do I remove the attachment from my RYOBI Power Head?
  • Stop the engine and disconnect the spark plug (if a gas unit), remove the battery (if using RYOBI 40V Power Head)
  • Loosen the knob at the connection point
  • Push in the button and twist the shafts to remove and separate the Power Head from the Attachment
How do I install my attachment to my RYOBI Power Head?
  • Stop the engine and disconnect the spark plug (if using a RYOBI Gas Power Head); remove the battery (if using the RYOBI 40V Power Head).
  • Loosen the knob on the coupler of the power head shaft and remove the end cap from the attachment (black rubber piece with loop hole for hanging).
  • Push in the silver button located on the attachment shaft. Align the button with the guide recess on the Power Head coupler and slide the two shafts together. Rotate the attachment shaft until the button locks into the positioning hole.

NOTE: If the button does not release completely in the positioning hole, the shafts are not locked into place. Slightly rotate from side to side until the button is locked into place.

  • Tighten the knob securely.

service & repair

Visit our replacmeent part store or our authorized service center locator for assistance with service and repairs.

rotate_counterclockwise rotate_clockwise upload caret--down snapchat instagram youtube facebook--square pinterest twitter facebook chevron--left play play speaker follow--outline settings--outline chat-bubble--ellipsis--outline like--outline chat-bubble--outline check chevron--up chevron--down ellipsis chat-bubble--ellipsis cast close close chevron--right home settings menu like chat-bubble--text chat-bubble user--outline user follow chat-bubble--user search add download keyboard_arrow_left keyboard_arrow_right Asset 1