Your one stop destination for tips & techniques, manuals, troubleshooting, FAQs and more!

18V ONE+ HP Compact Brushless 1/2" Drill/Driver Kit

18V ONE+ HP Compact Brushless 1/2" Drill/Driver Kit


Not Your Tool? Search Again

Tips & Techniques

Videos & Diagrams
Tips & Safety

Accessory Bit

There are bits for drilling holes and bits for driving fasteners.

Instructions: Loosen the chuck by hand, insert the drill bit's shank and tighten firmly.

Auger Bit

A bit used to "bore" or create deep holes in wood.

Awl hand tool

An Awl hand tool is a tool with a long metal spike used to mark or to drill holes in different materials.


The piece of metal that goes into the drill's tip. There are bits for drilling holes and bits for driving screws.

Black oxide bits

High Speed Steel Drill Bits with a Black Oxide finish which is created by a combination of chemicals and heat during the manufacturing process. Because of this finish, they have a higher resistance of rust and stay sharper longer; for use in general purpose drilling

Brad-point bit

A bit with 3 small points at the tip. Prevents the bit from "walking" when you start drilling. For precise drilling and for wood only.

Bubble Level

The water tube on the top and back of the drill that shows you when you are level with your drilling surface.


The cylinder that opens and closes the jaw of the drill.

Chuck Jaws

The portion at the very tip of the drill that holds the bit in place.

Chuck Key

An additional tool required to loosen and tighten the chuck.


The ring around the front of the drill (usually right behind the chuck) that lets you adjust the torque setting.

Clutch out

When the material you're driving into is too dense or tough for the clutch setting, the drill will stop moving the fastener. This is designed to protect your surface from damage. Adjust the clutch to a higher setting to complete the drive.


A bit that creates a pocket for the screw or fastener to fit in and be flush with the top of the material. The size of the pocket should match the size of the screw head. High Speed Steel countersinks can also be used to clean the edges of holes in metal and plastic.

Drill Bits

Used for drilling holes in various materials.

Driving/Screwdriving Bits

Forged or milled metal piece with a tip and a shank used for driving in all types of fasteners


Hardware that keeps two or more pieces of material together

Flush screw

A screw whose head is exactly level with the material it is fixed to. Might be used for molding or furniture

Fortsner Bit

A wood drilling bit that makes a clean flat bottom hole. These bits shoould only be used on a drill press because of high torque they produce.

Gear Switch

The switch on top that lets you choose between highest speed, and highest torque.

High Speed Drill Bits

General purpose bits used for drilling in wood, plastic, and metal. High Speed refers to the metal used to manufacture these kind of bits.

Hole Saw

A pilot drill bit attached to a cylindrical cutter. Used for making large holes, ussually in 2 by material; Can be used for installing lighting under cabinets

Impact rated bits

Driving bits manufactured with a special material or profile that withstand the high torque of an impact driver; for use with impact drivers

Keyless chuck

The kind of chuck that you can loosen and tighten by hand.

Lag screws

A Lag Screw is a heavy-duty wood screw used for structural support . Might be used for building a deck or trellis.

Lithium-Ion Battery

The most efficient kind of battery for a cordless drill. They typically charge faster, run longer, and don't slowly fade in power.

Masonry Bits

Drill bits with a carbide tip used to drill holes in brick, mortar, block and concrete.

Ni-Cad (Nickel Cadmium) Battery

The "old school" kind of battery. They tend to take longer to charge, and they gradually lose power as they run down.

Nut driver

A hex design bit used for driving in nuts, bolts and other hex head fasteners.

Pilot hole

Pilot holes are used primarily to prevent the wood from splitting. They can also be used to keep the screws on track and make it easier to drive.


A piece of wood used to cover a hole usually made by a fastener driven below the surface of the workpiece material. Might be used for decorative pieces

Pocket Hole

A hole is made for driving screws at an angle. Commonly used for furniture

Pocket hole jig

An accessory that helps you drill pocket holes.

Screw gauge

A chart with holes that can be used to determine the size of the screw to be used and the pilot hole needed.

Self-tapping screws

A fastener that makes its own hole as it's driven used for driving into sheet metal.


The section of the bit that goes into the drill's chuck. The most typical shanks are round, 3-flat, reduced and hex shaped.


To drive a fastener into material.

Spade bit / Paddle bit

A drilling bit with a flat, spade shaped head. Used for making larger holes.

Stripped/ Stripping Screws

A stripped screw has a head in which the tip design has been deformed by a spinning driver bit. They can be very hard to get out.

Sub flush screw

A screw whose head is below the surface of the material it is fixed to.

Tapered head wood-screws

A common type of fastener used for wood work.

Tile Bits / Glass Cutting Bits

Drill bits with a triangular carbide tip or tips used to drill holes in glass and tile.

Titanium coated drill bits

High Speed Steel Drill Bits with a Titanium Nitride coating which helps the drill bit stay cooler when in use, especially when drilling metal. This helps the drill bit stay sharper longer. For general purpose drilling


A drill's word for power. High torque means the drill/driver is turning the bit very hard.

In The Box


  • Brushless Compact 1/2 in. Drill/Driver - psbdd01

  • Brushless Compact 1/2 in. Drill/Driver - psbdd01


Ryobi three year warranty logo

This product is covered by a 3-year limited warranty.

service & repair

Visit our replacmeent part store or our authorized service center locator for assistance with service and repairs.

rotate_counterclockwise rotate_clockwise upload caret--down snapchat instagram youtube facebook--square pinterest twitter facebook chevron--left play play speaker follow--outline settings--outline chat-bubble--ellipsis--outline like--outline chat-bubble--outline check chevron--up chevron--down ellipsis chat-bubble--ellipsis cast close close chevron--right home settings menu like chat-bubble--text chat-bubble user--outline user follow chat-bubble--user search add download keyboard_arrow_left keyboard_arrow_right Asset 1